Clik here to view.
Rev-shot Write up
Introduction: Fist off I would like to say that I am doing this wright up because I have had quite a few people ask me to do it and since there isn't a lot of revshots around and the original wright...
View ArticleEB-1 longhorn rifle
This is the final product minus the switch of my electronic blowgun the final name is the longhorn rifle it fires about 70-85 fps with the ability to fire two rounds at once here is the YouTube link...
View ArticleQuadshot catch templates?
Does anyone have templates, measurements, etc. for a Quadshot catch? I thrifted one and the catch is broken, so I need to machine a new one.
View ArticlePetg 3d printing! Make your own tubes and catches with super stron
Why hello there boy and girls of the internet and nerf fans all around. Im sure you know that most writeups here on the 'haven use the imperial system and not metric. So how are other people from other...
View ArticleTemplates?
How do I make templates for working with sheets of polycarb? Should I use Inventor? AutoCAD? Something else?
View ArticleClik here to view.
Tornadowbow help
Hello everyone. As some of you know, I thrifted a Koosh Vortex Tornado a while back, and now I want to turn it into a Tornadobow. This thread is intended to request help and ask a few questions about...
View ArticlePCSR and 3D printed homemade parts? Aeromech, thoughts?
So I'm currently borrowing a 3rd printer. Its the Dremel Idea Builder aka a Flashforge Dreamer without the heated plate. Anyway, it only uses PLA not ABS. I was wondering if I would run into too many...
View ArticleClik here to view.
Constant Force spring blaster infodump
A while back I posted this in the homemades pictures thread. In short, it was a blaster whose energy source was a constant force spring, like the kind used in Raider drums or your tape measure....
View ArticleClik here to view.
How to control a blaster with Arduino
I thought I would share some code I have cobbled together for controlling my brushless Stryfe with an arduino controller. This allows for push button spin-up and you don't need to use a servo tester...
View ArticleThe STAN gun
The S imple T ype A utomatic N erf gun. Materials: 18" Schedule 80 1/2" PVC Pipe 5.85 (120") http://www.mcmaster.com/#48855k11 30"+ Schedule 40 1/2" PVC Pipe 2.21 (120")...
View ArticleClik here to view.
Definitive Guide to 3D Printing
FOREWARD This guide is in response to the several emails per month I receive about 3D printing, and it is easier to throw everything out there once than having to regurgitate the same information a...
View ArticleClik here to view.
Nerf Gun Gambol Shroud (RWBY cosplay)
Back again! My latest nerf cosplay prop is Blake Belladonnas Gambal shroud from the show RWBY! I used the nerf Stealth X3 (I think that's the name) pvc board, lots of foam and glue and was able to...
View ArticleClik here to view.
Spring Binding in Floating-Plunger-Head SNAP
Ok. This is the third time I’ve typed this out, so this had better not suddenly disappear on me like the last two copies. I recently built a prototype of a homemade that I designed. I have run into...
View ArticleClik here to view.
Fix for Omnideirectional Plunger Rod Binding/False Catching
So my distaste for omnidirection plunger rods is not unknown to the nerf community, up til now, they seemed to catch less reliably than unidirectional catches, and were overall more fickle. The problem...
View ArticleClik here to view.
Your First Snap
Intended for this contest but can/will serve as your normal writeup for other purposes. This blaster is meant for new guys who have been exposed, usually online, to this little realm of nerf called...
View ArticleClik here to view.
3D printing a flywheel blaster
Hey everyone, Hope this is the right place to post, I wasn't sure if this belonged here, or as a concept thread. Basically, I'm hoping to 3D print a nerf flywheel blaster using a PLA printer with a...
View ArticleClik here to view.
DCHAP-3
I found this link: http://www.sscentral.org/homemade/check_valves.html The stem valves used in that article can be bought in bulk lots on eBay, and you end up only paying $0.30 to $0.50 each. If you...
View ArticleClik here to view.
HR-1 Rifle
Well guys here comes my first homemade the HR-1 it is a slamfire design that isnt very accurate if you don't know how to use it. I do have a few sealing issues that I am working on. This blaster...
View ArticleClik here to view.
Slotless Bullpup Snapbow
Slotless Bullpup Snap (SBS) (Using this name until someone gives me a better one) This is my entry for Aeromech’s homemades contest, which I think is super cool and good of him and Draconis to...
View ArticleClik here to view.
Plusbow Rev. 3
Plusbow Rev.3 Guide Instructables Mirror Design Goals Reduce Part count Two Options for Plunger tubes and Plungers (+bow or 2-11) Omni-directional catch Spring guide to remove "serpentine"...
View Article